Flir
Direct Workday career site

First Article Assembler- Solder

Location
San Diego, CA
Listed
Today

About the role

Be visionary

Teledyne Technologies Incorporated provides enabling technologies for industrial growth markets that require advanced technology and high reliability. These markets include aerospace and defense, factory automation, air and water quality environmental monitoring, electronics design and development, oceanographic research, deepwater oil and gas exploration and production, medical imaging and pharmaceutical research.

We are looking for individuals who thrive on making an impact and want the excitement of being on a team that wins.

General Overview

Under limited supervision performs a wide variety of highly skilled, complex and non-repetitive electronic and electro-mechanical assembly operations of a semi-skilled or complex nature where documentation and guidance are limited.

Can perform assembly operations where complete information is not readily available or follows assembly shop and production operation sheets, wire lists, samples, drawings, schematic and verbal instructions to perform a wide variety of complex assembly operations. Understands implications of work and makes recommendations for solutions. May train employees on basic assembly procedures within a given work area.

Essential Duties and Responsibilities include the following. Other duties may be assigned.

  • Perform wire preparation tasks including stripping, tinning, lead prep, and termination
  • Hand solder wires and cables to high density and/or low profile connectors while maintaining industry workmanship standards
  • Crimp, stake, fasten, and secure wires, connectors, terminals, and contacts using hand crimp tools and pneumatic crimp tools.
  • Perform complex wire and cable harness assembly operations, including:
  • Point-to-point wiring
  • Harness routing, lacing, and tie-down
  • Chassis and panel wiring
  • Assemble wire harnesses and cables per:
  • Electrical schematics
  • Wiring diagrams
  • Assembly drawings & BOMs
  • Work instructions
  • Support First Article Assembly (FAI) builds, including:
  • Building initial units from new or revised drawings
  • Identifying drawing discrepancies or build issues
  • Providing feedback to engineering and manufacturing teams
  • Install and route components to meet electrical, mechanical, and workmanship requirements
  • Use hand tools and small power tools to assemble connectors, cables, and assembly components components
  • Perform visual in-process inspections, go/no-go testing, continuity testing, IR testing, and automated electrical testing
  • Troubleshoot wiring defects and perform rework or repair on rejected assemblies
  • Perform work under a microscope as required for soldering or inspection
  • Support additional processes such as:
  • Labeling and color-coding
  • Part trimming and finishing
  • Epoxy application, potting, encapsulation, and curing
  • Follow all safety procedures, including proper handling of chemicals and materials
  • Accurately complete production documentation, First Article records, and quality logs
  • Ensure quality checks are completed throughout the manufacturing process
  • Provide basic training or guidance to less experienced assemblers as needed

Supervisory Responsibilities

This position does not supervise other employees.

Qualifications/Requirements

Education/Experience

  • Requires a high school education or equivalent. Trade school certification preferred.
  • Minimum of 5 years closely related custom/prototype assembly experience in an electromechanical environment. Preferred experience of hands-on wire & cable harness assembly experience.
  • Demonstrated experience with:
  • Wire stripping, tinning, crimping, and soldering
  • Cable & Harness Routing and Termination
  • Experience supporting First Article Assembly (FAI) builds
  • Ability to independently read and interpret:
  • Wiring diagrams and schematics
  • Assembly drawings and Bills of Material (BOMs)
  • Advanced Experience using:
  • Hand tools and crimp tools
  • Soldering equipment
  • Basic electrical test equipment (e.g., continuity testers, volt meters)
  • Strong manual dexterity and attention to detail
  • Experience performing inspection, rework, and repair
  • Ability to follow detailed work instructions and workmanship standards
  • Willingness and availability to work overtime, including weekends, as required
  • IPC/J standard soldering training and certification is highly preferred.
  • Demonstrated knowledge of lean manufacturing and Kanban systems preferred.
  • Basic computer skills (Outlook, MS Excel, MS Word) needed to perform the required duties.
  • Must possess U.S. citizenship or be a "U.S. Person". (A U.S. Person is defined as a person who is a lawful permanent resident "Green Card holder" as defined by 8 U.S.C. 1101 (a)(20) or who is a "Protected Individual" as defined by 8 U.S.C. 1324b(a)(3).)

Salary Range

$50,600.00-$67,500.000

The anticipated salary range listed for this role is only an estimate. Actual compensation for successful candidates is carefully determined based on several factors including, but not limited to, location, education/training, work experience, key skills, and type of position.

Teledyne conducts background checks on qualified applicants who receive a conditional offer of employment in accordance with applicable laws, regulations and ordinances. Background checks may include, but are not limited to, education verification, employment history and verification, criminal convictions, Motor Vehicle Report (MVR & driving history), reference check, credit checks/credit history and drug testing.

Teledyne and all of our employees are committed to conducting business with the highest ethical standards. We require all employees to comply with all applicable laws, regulations, rules and regulatory orders. Our reputation for honesty, integrity and high ethics is as important to us as our reputation for making innovative sensing solutions.

Read the original posting

From Flir's careers page, first listed on Rolev.ai on November 17, 2026. Rolev.ai is not the employer.

How Rolev.ai helps with this application

Rolev.ai is a job search and application tool for US job seekers. For this First Article Assembler- Solder role at Flir, it shows how your resume fits, tailors your resume to the posting, and prepares the application for you to review.

  • See how you fit

    Openings from employer career sites are ranked against your whole resume—and searchable inside Claude, ChatGPT, and Cursor via Rolev.ai MCP.

  • Tailor without inventing

    Every change to your resume is checked against your original. New experience goes in only with your yes—zero fabricated claims.

  • Draft the full kit

    Tailored and Full Match resumes, role-specific cover letters, and answers to employer screening questions are prepared in seconds.

  • 1-Click Extension Autofill

    The Chrome extension fills the employer's Greenhouse, Workday, Lever, or Ashby form in 1 click. You review it and press Submit.

Common questions

Where is the First Article Assembler- Solder job at Flir located?

This First Article Assembler- Solder position at Flir is located in San Diego, CA. Always check Flir's application page for specific state eligibility or relocation policies.

How do I apply for the First Article Assembler- Solder position at Flir?

This listing links directly to Flir's Workday application page. You can apply directly on Flir's site, or use Rolev.ai to check your resume fit, generate a zero-hallucination tailored resume and cover letter for this posting, and autofill the Workday application form in 1 click with the Rolev.ai Chrome extension. You always review the form and press Submit yourself.